We offer commercial roof repair services in Radcliff for flat membrane roofs, metal buildings, active leaks, and industrial plant roofs, each starting with an inspection.
Our commercial roof repair services in Radcliff cover four lines of work, each matched to a roof type or to how a building is used.
Single-ply and built-up roofs on offices, shops, and storefronts get seam, blister, puncture, flashing, and drain repairs with materials matched to the existing membrane, so a TPO lap gets a weld and an EPDM lap gets tape.
Repair Includes
Metal panel roofs on shops, warehouses, and farm buildings get fastener, lap, rust, gutter, ridge, and skylight repairs, with every screw row walked rather than only the one above the stain.
Repair Includes
Leaks of unknown origin get traced from inside to outside, along deck flutes and purlins, with moisture readings showing how far the water spread before any patch is chosen.
Repair Includes
Plant roofs get repairs planned around shifts, exhaust, air intakes, and heavy rooftop equipment, coordinated through the plant safety contact and logged on a roof map.
Repair IncludesMatch the roof you have to the repair that usually starts the job. The last case points past repair.
Single-ply laps peel or split at T-joints and curb corners, while moisture readings around them stay dry.
Washers have cracked and screws have backed out of the purlins, and end laps near the eave seep.
Water appears inside with nothing visibly broken right above it, often after wind-driven rain.
Repair logs show many small leaks in one area, and core cuts find wet insulation under the membrane there.
Send the address and roof type, and the inspection will sort the roof into the right repair line.
Get A Free EstimateEvery service line follows the same visit order, with steps added for metal buildings and plants.
We begin under the leak, record the stain with photos, and then check the roof above for failed seams, flashing, drains, and fasteners.
Probes, controlled water tests, and a look at the roof uphill of the stain pin down where water gets in before any material is chosen.
Readings around the problem show whether the board is dry enough for a patch or needs cutting out first, and core cuts confirm the readings where the meter is unclear.
Membrane, flashing, fasteners, or panels go in to match the roof that is there, installed the way the roof maker specifies.
Drains near the work get cleared, the repaired spots get photographed, and the record goes into your building file so the next inspection starts from known repairs.
Question about your own roof?
Call UsAt transitions, where the membrane or panel meets a curb, wall, drain, pipe, or another piece of roofing. On TPO and PVC that means unwelded spots, T-joints, curb corners, and boots; on EPDM, peeling laps and shrinkage at walls; on bitumen, blisters and open laps at drains; on metal, screw washers, end laps, ridge caps, and gutters.
A walk of those spots after each storm season catches leaks early.
Mostly how much wet material comes out, how hard the leak is to reach, and how many spots need work. The size and number of leak areas, wet insulation under the membrane, roof access, the membrane type, flashing at curbs and walls, and work-hour limits around the building all play in.
A leak caught at one open seam costs far less than one that soaked a whole bay.
Roof improvements to existing nonresidential buildings can qualify, according to IRS Publication 946, and whether a given repair is expensed or capitalized is a question for a CPA. For 2026 the maximum deduction is $2,560,000, with the phase-out starting once qualifying property passes $4,090,000.
Ask the CPA how membrane or deck replacements are classified and how invoices should separate repair work from new roof sections.
In the same order every time: inspect your roof starting at the interior leak point, trace the water path to the entry point, take moisture readings, make a temporary repair if rain is coming, complete the permanent repair with matching materials, recheck the drains, seams, and flashing nearby, and record the repair with photos for the owner’s file.
Yes.
Many Radcliff area buildings pair a metal warehouse or shop with a low-slope office wing or addition. The inspection walks both roofs, and the repair uses the right method for each: welds, tape, or bitumen patches on the membrane side, and fasteners, lap tape, and stitch screws on the metal side, with the transition flashing between them checked too.
Yes. The repair follows the membrane or panel that is on the roof, whoever installed it. A TPO roof gets TPO patches and welds, an EPDM roof gets EPDM tape and primer, and a metal roof gets fasteners and panels matched to its profile. Past repair records from any company help the trace.
Request a free estimate, or call to talk through which repair line fits your roof.
Leave a name and number and we will call you back.
Prefer to talk now? Call (930) 201-5321